Standard six-string guitar tuning is E2–A2–D3–G3–B3–E4, from string 6 to string 1. Tune one string at a time, confirm its note and octave, then recheck the set. Alternate tunings change those string targets; changing A4 calibration is a different operation.
Start with the correct instrument and string setup. A familiar chord shape can produce a different chord after retuning, and some upward tuning changes increase tension enough to require maker or technician advice.
Standard tuning notes and frequencies
| String | Note | Frequency |
|---|---|---|
| 6, lowest | E2 | 82.41 Hz |
| 5 | A2 | 110.00 Hz |
| 4 | D3 | 146.83 Hz |
| 3 | G3 | 196.00 Hz |
| 2 | B3 | 246.94 Hz |
| 1, highest | E4 | 329.63 Hz |
The two E strings are two octaves apart. An E label without an octave can therefore be misleading. Check string number and frequency rather than tightening a string until any E appears.
How to tune one string
- Confirm the intended tuning and reference, commonly A4=440.
- Mute strings you are not checking.
- Pluck one open string at a moderate consistent strength.
- Allow the initial attack to settle when reading the sustained pitch.
- Make small adjustments while checking the note and octave.
- Recheck after the whole set has been adjusted.
The guitar tuner can provide standard string targets. A chromatic tuner is useful when you know the desired alternate notes.
If tension or the sound becomes unexpected, stop and verify the target. Do not continue turning a peg simply because a microphone reading is missing.
Ten alternate tunings with octave labels
| Tuning | Open-string notes | Change from standard |
|---|---|---|
| Drop D | D2 A2 D3 G3 B3 E4 | Lower string 6 from E2 to D2. |
| Half step down | Eb2 Ab2 Db3 Gb3 Bb3 Eb4 | Lower every string by one semitone. |
| Whole step down | D2 G2 C3 F3 A3 D4 | Lower every string by two semitones. |
| Open G | D2 G2 D3 G3 B3 D4 | Lower strings 6, 5 and 1 from standard. |
| Open D | D2 A2 D3 F#3 A3 D4 | Lower strings 6, 3, 2 and 1. |
| DADGAD | D2 A2 D3 G3 A3 D4 | Lower strings 6, 2 and 1. |
| Drop C | C2 G2 C3 F3 A3 D4 | Whole step down, then lower string 6 a further tone. |
| Open E | E2 B2 E3 G#3 B3 E4 | Raises several strings; confirm suitability before retuning. |
| Double Drop D | D2 A2 D3 G3 B3 D4 | Lower strings 6 and 1. |
| Open A | E2 A2 E3 A3 C#4 E4 | Raises several strings; confirm suitability before retuning. |
The flats in half-step-down tuning are note spellings, not instructions to tune vaguely below pitch. For example, Eb2 is one semitone below E2; it is not a slightly flat E2.
Drop, open and modal tunings serve different purposes
Drop D lowers only the sixth string, giving D2–A2–D3 across the bottom three strings. This enables a convenient movable power-chord shape, but standard shapes involving the sixth string need reconsideration.
Open G and Open D form major-chord pitch collections when the open strings sound together. DADGAD does not include a major third in its open collection, leaving a different harmonic starting point.
Half-step-down and whole-step-down tunings preserve standard interval relationships across the strings. Their familiar shapes therefore move together to lower sounding keys.
Be careful with Open E and Open A
These tunings raise several strings relative to standard. Instrument construction, string gauge and setup affect whether a change is appropriate. Do not assume every acoustic or electric guitar should be retuned upward using the same strings.
A lower open tuning plus a capo can sometimes provide a corresponding sounding chord without the same upward retuning. Open D with a capo at fret two sounds an E-major open collection; Open G with a capo at fret two sounds an A-major collection.
The capo changes sounding pitch and effective playing length. Document the underlying tuning and capo position separately rather than calling every arrangement the same open-string setup.
A capo is not a different reference pitch
A capo raises the sounding pitches according to its position. It does not turn an A440 tuner into A432. Depending on placement and pressure, it can also affect individual-string intonation.
Check tuning with the capo in the performance position when appropriate. If notes become unexpectedly sharp, investigate pressure, position and setup rather than changing the reference to hide the discrepancy.
The A440 guide explains calibration, while the tuner-mode comparison explains target selection.
Why open strings can be right but chords sound wrong
Open-string tuning is only one part of fretted-note intonation. String condition, action, nut height, scale compensation and fretting pressure can affect other notes.
A common check compares a fretted octave region with the appropriate octave reference. It can reveal a problem, but one reading does not specify every needed repair. Seek setup guidance for persistent discrepancies.
Do not try to fix all fretted notes by making the open string intentionally wrong. Test a consistent passage and identify whether the issue is technique, setup or the chosen musical reference.
Choose an alternate tuning for the music
Begin with the desired sound or fingering task, not a claim that one tuning is universally best. Drop D is a small first change; open tunings reorganise chord shapes; larger downward changes may need a different string setup.
Save the note list and check each octave before playing. A tuning name alone can have variants, especially across different instruments and string counts.
The note-frequency chart supplies calculated targets when a particular octave is unclear.
Frequently asked questions
Can I tune all six strings at once with a single-note detector?
No complete multi-string analysis is implied. Use one isolated string unless the specific tuner supports polyphonic tuning.
Why does a new string keep moving?
New strings and changes in setup can require settling and rechecking. Follow the maker’s fitting guidance rather than making large repeated adjustments.
Should the tuner always be at zero?
Compare with the intended reference and stable portion of the string sound. Tiny movement during attack or decay does not automatically require another peg turn.
Does a lower tuning always need thicker strings?
There is no universal answer. Desired tension, scale length and setup matter. Consult suitable guidance before major changes.
Can changing tuning damage a guitar?
Inappropriate tension or setup changes can cause problems. Verify raised tunings and unusual changes with the maker or a qualified technician.
Reference basis: Fender alternate-tuning material, D’Addario setup guidance and standard equal-tempered note calculations. No specific instrument was retuned for this article.
